点亮LED灯_STM32第一课

基本原理

初始化Hal库

HAL_Init();

系统时钟

SystemClock_Config();

 

GPIOB初始化：GPIOB模式为推挽输出，GPIO引脚为Pin_5、0、1代表红绿蓝LED，既不上拉也不下拉电阻，低速

HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);

控制GPIO输出：引脚GPIOB，5号0号1号，低电平点亮

HAL_GPIO_WritePin(RED_GPIO_Port, RED_Pin, LED_ON);

以下是详细文件

main.c

#include "main.h"

#include "gpio.h"

void SystemClock_Config(void);

void Error_Handler(void);

int main(void) {

    HAL_Init();

    SystemClock_Config();

    MX_GPIO_Init();

    while (1) {

        //设置GPIOB中红绿蓝Led的亮灭

        HAL_GPIO_WritePin(RED_GPIO_Port, RED_Pin, LED_ON);

        HAL_Delay(1000);

        HAL_GPIO_WritePin(RED_GPIO_Port, RED_Pin, LED_OFF);

        HAL_GPIO_WritePin(GREEN_GPIO_Port, GREEN_Pin, LED_ON);

        HAL_Delay(1000);

        HAL_GPIO_WritePin(GREEN_GPIO_Port, GREEN_Pin, LED_OFF);

        HAL_GPIO_WritePin(BLUE_GPIO_Port, BLUE_Pin, LED_ON);

        HAL_Delay(1000);

        HAL_GPIO_WritePin(BLUE_GPIO_Port, BLUE_Pin, LED_OFF);

    }

}

/**

  * @brief System Clock Configuration

  * @retval None

  */

void SystemClock_Config(void) {

    RCC_OscInitTypeDef RCC_OscInitStruct = {0};

    RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};

    /** Initializes the RCC Oscillators according to the specified parameters

    * in the RCC_OscInitTypeDef structure.

    */

    RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;

    RCC_OscInitStruct.HSEState = RCC_HSE_ON;

    RCC_OscInitStruct.HSEPredivValue = RCC_HSE_PREDIV_DIV1;

    RCC_OscInitStruct.HSIState = RCC_HSI_ON;

    RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;

    RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;

    RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL9;

    if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {

        Error_Handler();

    }

    /** Initializes the CPU, AHB and APB buses clocks

    */

    RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK

                                  | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;

    RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;

    RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;

    RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;

    RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;

    if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK) {

        Error_Handler();

    }

}

/**

  * @brief  This function is executed in case of error occurrence.

  * @retval None

  */

void Error_Handler(void) {

    /* USER CODE BEGIN Error_Handler_Debug */

    /* User can add his own implementation to report the HAL error return state */

    __disable_irq();

    while (1) {

    }

    /* USER CODE END Error_Handler_Debug */

}

#ifdef  USE_FULL_ASSERT

/**

  * @brief  Reports the name of the source file and the source line number

  *         where the assert_param error has occurred.

  * @param  file: pointer to the source file name

  * @param  line: assert_param error line source number

  * @retval None

  */

void assert_failed(uint8_t *file, uint32_t line)

{

  /* USER CODE BEGIN 6 */

  /* User can add his own implementation to report the file name and line number,

     ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */

  /* USER CODE END 6 */

}

#endif /* USE_FULL_ASSERT */

　　main.h

#ifndef __MAIN_H

#define __MAIN_H

#ifdef __cplusplus

extern "C" {

#endif

#include "stm32f1xx_hal.h"

#define GREEN_Pin       GPIO_PIN_0

#define GREEN_GPIO_Port GPIOB

#define BLUE_Pin        GPIO_PIN_1

#define BLUE_GPIO_Port  GPIOB

#define RED_Pin         GPIO_PIN_5

#define RED_GPIO_Port   GPIOB

#define LED_ON          GPIO_PIN_RESET

#define LED_OFF         GPIO_PIN_SET

#ifdef __cplusplus

}

#endif

#endif /* __MAIN_H */

gpio.c

#include "gpio.h"

void MX_GPIO_Init(void) {

    GPIO_InitTypeDef GPIO_InitStruct = {0};

    /* GPIO Ports Clock Enable */

    __HAL_RCC_GPIOB_CLK_ENABLE();

    __HAL_RCC_GPIOA_CLK_ENABLE();

    /*Configure GPIO pins : PBPin PBPin PBPin */

    GPIO_InitStruct.Pin = GREEN_Pin | BLUE_Pin | RED_Pin;

    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;

    GPIO_InitStruct.Pull = GPIO_NOPULL;

    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;

    HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);

}

　　

gpio.h

#ifndef __GPIO_H__

#define __GPIO_H__

#ifdef __cplusplus

extern "C" {

#endif

#include "main.h"

void MX_GPIO_Init(void);

#ifdef __cplusplus

}

#endif

#endif /*__ GPIO_H__ */

　　

配置过程

点亮LED灯_STM32第一课的相关教程结束。