目录
主备备份双机热备配置
负载分担双机热备配置
为了解决多个VRRP备份组状态不一致的问题，华为防火墙引入VGMP（VRRP Group Management Protocol）来实现对VRRP备份组的统一管理，保证多个VRRP备份组状态的一致性。我们将防火墙上的所有VRRP备份组都加入到一个VGMP组中，由VGMP组来集中监控并管理所有的VRRP备份组状态。如果VGMP组检测到其中一个VRRP备份组的状态变化，则VGMP组会控制组中的所有VRRP备份组统一进行状态切换，保证各VRRP备份组状态的一致性。双机热备协议HRP（Huawei Redundancy Protocol）协议是承载在VGMP(Vrrp Group Management Protocol)报文上进行传输的，在Master和Backup防火墙设备之间备份关键配置命令和会话表状态信息，是双机热备协议。VGMP、HRP是华为私有协议
主备备份双机热备配置
在主备备份双机热备模式下，FW1既是PC1的网关也是PC2的网关，也是AR1回去的路由的默认下一跳。在主备备份双机热备模式下，假如FW1宕机了，FW2会立刻切换到Active状态，从而不影响主机与外界通信。
如图，PC1和PC2是企业内网的主机，属于不同的VLAN。AR1是边界路由器。FW1和FW2是企业内部防火墙，他们之间形成双机热备，FW1是active状态，FW2是standby状态。企业内网通过AR1的出端口通过NAT方式访问外网。在防火墙FW1上还配置链路追踪功能，追踪AR2的g0/0/0口，如果到达不了，则切换状态。AR1下面的配置
PC1
PC>ipconfig
IPv4 address......................: 192.168.1.10
Subnet mask.......................: 255.255.255.0
Gateway...........................: 192.168.1.254
Physical address..................: 54-89-98-30-73-39
Vlan .............................: 10PC2
PC>ipconfig
IPv4 address......................: 192.168.2.10
Subnet mask.......................: 255.255.255.0
Gateway...........................: 192.168.2.254
Physical address..................: 54-89-98-AF-62-C9
Vlan..............................: 20LSW1
#
vlan batch 10 20
#
interface GigabitEthernet0/0/1
port link-type trunk
port trunk allow-pass vlan 10 20
#
interface GigabitEthernet0/0/2
port link-type trunk
port trunk allow-pass vlan 10 20
#
interface GigabitEthernet0/0/3
port link-type access
port default vlan 10
#
interface GigabitEthernet0/0/4
port link-type access
port default vlan 20
#
FW1
#
hrp enable
hrp interface GigabitEthernet1/0/0 remote 10.1.1.2
hrp preempt delay 10
hrp track ip-link track
#
ip-link check enable
ip-link name track
destination 20.0.0.2 mode icmp
#
interface GigabitEthernet1/0/0
undo shutdown
ip address 10.1.1.1 255.255.255.252
#
interface GigabitEthernet1/0/1.10
vlan-type dot1q 10
ip address 192.168.1.1 255.255.255.0
vrrp vrid 10 virtual-ip 192.168.1.254 active
#
interface GigabitEthernet1/0/1.20
vlan-type dot1q 20
ip address 192.168.2.1 255.255.255.0
vrrp vrid 20 virtual-ip 192.168.2.254 active
#
interface GigabitEthernet1/0/2
undo shutdown
ip address 192.168.3.1 255.255.255.0
vrrp vrid 30 virtual-ip 192.168.3.254 active
#
firewall zone trust
set priority 85
add interface GigabitEthernet0/0/0
add interface GigabitEthernet1/0/1.10
add interface GigabitEthernet1/0/1.20
#
firewall zone untrust
set priority 5
add interface GigabitEthernet1/0/2
#
firewall zone name heartbeat id 4
set priority 80
add interface GigabitEthernet1/0/0
#
ip route-static 0.0.0.0 0.0.0.0 192.168.3.3
#
#
security-policy
rule name TRUST_UN_TRUST
source-zone trust
destination-zone untrust
service icmp
action permit
# FW2
#
hrp enable
hrp interface GigabitEthernet1/0/0 remote 10.1.1.1
hrp preempt delay 10
#
interface GigabitEthernet1/0/1
undo shutdown
#
interface GigabitEthernet1/0/1.10
vlan-type dot1q 10
ip address 192.168.1.2 255.255.255.0
vrrp vrid 10 virtual-ip 192.168.1.254 standby
#
interface GigabitEthernet1/0/1.20
vlan-type dot1q 20
ip address 192.168.2.2 255.255.255.0
vrrp vrid 20 virtual-ip 192.168.2.254 standby
#
interface GigabitEthernet1/0/2
undo shutdown
ip address 192.168.3.2 255.255.255.0
vrrp vrid 30 virtual-ip 192.168.3.254 standby
#
firewall zone trust
set priority 85
add interface GigabitEthernet0/0/0
add interface GigabitEthernet1/0/1.10
add interface GigabitEthernet1/0/1.20
#
firewall zone untrust
set priority 5
add interface GigabitEthernet1/0/2
#
firewall zone name heartbeat id 4
set priority 80
add interface GigabitEthernet1/0/0
#
ip route-static 0.0.0.0 0.0.0.0 192.168.3.3
#
security-policy
rule name TRUST_UN_TRUST
source-zone trust
destination-zone untrust
service icmp
action permit
# AR1
#
acl number 2000
rule 5 permit source 192.168.2.0 0.0.0.255
rule 10 permit source 192.168.1.0 0.0.0.255
#
interface GigabitEthernet0/0/0
ip address 192.168.3.3 255.255.255.0
#
interface GigabitEthernet0/0/2
ip address 20.0.0.1 255.255.255.0
nat outbound 2000
#
ip route-static 192.168.1.0 255.255.255.0 192.168.3.254
ip route-static 192.168.2.0 255.255.255.0 192.168.3.254
#AR2
#
interface GigabitEthernet0/0/0
ip address 20.0.0.2 255.255.255.0
#负载分担双机热备配置
在负载分担双机热备模式下，FW1是PC1的网关，FW2是PC2的网关。AR1回往PC1的下一跳是PC1，AR2回往PC2的下一跳是PC2。FW1和FW2之间形成负载分担双机热备关系，其实任何一个防火墙的接口down了，都不影响主机和外接通信。
如图，PC1和PC2是企业内网的主机，属于不同的VLAN。AR1是边界路由器。FW1和FW2是企业内部防火墙，他们之间形成双机热备，FW1既有active状态也有standby状态，FW2既有active状态也有standby状态。企业内网通过AR1的出端口通过NAT方式访问外网。
PC1
PC>ipconfig
IPv4 address......................: 192.168.1.10
Subnet mask.......................: 255.255.255.0
Gateway...........................: 192.168.1.254
Physical address..................: 54-89-98-30-73-39
Vlan..............................: 10PC2
PC>ipconfig
IPv4 address......................: 192.168.2.10
Subnet mask.......................: 255.255.255.0
Gateway...........................: 192.168.2.254
Physical address..................: 54-89-98-AF-62-C9
Vlan..............................: 20LSW1
[SW1]display current-configuration
#
vlan batch 10 20
#
interface GigabitEthernet0/0/1
port link-type trunk
port trunk allow-pass vlan 10 20
#
interface GigabitEthernet0/0/2
port link-type trunk
port trunk allow-pass vlan 10 20
#
interface GigabitEthernet0/0/3
port link-type access
port default vlan 10
stp edged-port enable
#
interface GigabitEthernet0/0/4
port link-type access
port default vlan 20
stp edged-port enable
#FW1
HRP_M[FW1]display current-configuration
#
hrp enable
hrp interface GigabitEthernet1/0/0 remote 10.1.1.2
#
interface GigabitEthernet1/0/1.10
vlan-type dot1q 10
ip address 192.168.1.1 255.255.255.0
vrrp vrid 10 virtual-ip 192.168.1.254 active
#
interface GigabitEthernet1/0/1.20
vlan-type dot1q 20
ip address 192.168.2.1 255.255.255.0
vrrp vrid 20 virtual-ip 192.168.2.254 standby
#
interface GigabitEthernet1/0/2
undo shutdown
ip address 192.168.3.1 255.255.255.0
vrrp vrid 30 virtual-ip 192.168.3.253 active
vrrp vrid 40 virtual-ip 192.168.3.254 standby
#
firewall zone trust
set priority 85
add interface GigabitEthernet0/0/0
add interface GigabitEthernet1/0/1.10
add interface GigabitEthernet1/0/1.20
add interface GigabitEthernet1/0/1
#
firewall zone untrust
set priority 5
add interface GigabitEthernet1/0/2
#
firewall zone name heartbeat id 4
set priority 80
add interface GigabitEthernet1/0/0
#
ip route-static 0.0.0.0 0.0.0.0 192.168.3.3
#
security-policy
rule name TRUST_TO_UNTRUST
source-zone trust
destination-zone untrust
service icmp
action permit
#
FW2
HRP_S[FW2]display current-configuration
#
hrp enable
hrp interface GigabitEthernet1/0/0 remote 10.1.1.1
#
interface GigabitEthernet1/0/0
undo shutdown
ip address 10.1.1.2 255.255.255.252
#
interface GigabitEthernet1/0/1.10
vlan-type dot1q 10
ip address 192.168.1.2 255.255.255.0
vrrp vrid 10 virtual-ip 192.168.1.254 standby
#
interface GigabitEthernet1/0/1.20
vlan-type dot1q 20
ip address 192.168.2.2 255.255.255.0
vrrp vrid 20 virtual-ip 192.168.2.254 active
#
interface GigabitEthernet1/0/2
undo shutdown
ip address 192.168.3.2 255.255.255.0
vrrp vrid 30 virtual-ip 192.168.3.253 standby
vrrp vrid 40 virtual-ip 192.168.3.254 active
#
firewall zone trust
set priority 85
add interface GigabitEthernet0/0/0
add interface GigabitEthernet1/0/1
add interface GigabitEthernet1/0/1.10
add interface GigabitEthernet1/0/1.20
#
firewall zone untrust
set priority 5
add interface GigabitEthernet1/0/2
#
firewall zone name heartbeat id 4
set priority 80
add interface GigabitEthernet1/0/0
#
ip route-static 0.0.0.0 0.0.0.0 192.168.3.3
#
security-policy
rule name TRUST_TO_UNTRUST
source-zone trust
destination-zone untrust
service icmp
action permit
#
AR1
[AR1]display current-configuration
#
acl number 2000
rule 5 permit source 192.168.1.0 0.0.0.255
rule 10 permit source 192.168.2.0 0.0.0.255
#
interface GigabitEthernet0/0/0
ip address 192.168.3.3 255.255.255.0
#
interface GigabitEthernet0/0/2
ip address 20.0.0.1 255.255.255.0
nat outbound 2000
#
ip route-static 192.168.1.0 255.255.255.0 192.168.3.253
ip route-static 192.168.2.0 255.255.255.0 192.168.3.254
#
AR2
[AR2]display current-configuration
#
interface GigabitEthernet0/0/0
ip address 20.0.0.2 255.255.255.0
#
VRRP和VGMP官方参考：https://forum.huawei.com/enterprise/zh/thread-282263.html
附上负载分担模式下的ensp源文件：链接: https://pan.baidu.com/s/1S5xzALnyg8cmn_lTB_jd_w 密码: yez5
